If you would like to upgrade to a newer long-term support version of Studio Pro, see Moving from Mendix Studio Pro 8 to 9.

Debug Microflows

Last modified: August 27, 2024

Introduction

Mendix Studio Pro has a built-in consistency checker that validates if the application you are building contains any obvious errors. This dramatically reduces the amount of technical errors during run-time, but Studio Pro isn’t able to check if your app contains functional errors. This is mainly a manual practice, but Mendix does support enough tools to make this easier. If you run into a functional error in any of the microflows, you can easily debug them with the debugger.

This how-to teaches you how to do the following:

  • Use breakpoints
  • Debug microflows

Prerequisites

Before starting this how-to, make sure you have completed the following prerequisites:

Debugging Overview

There are three debugging panes to be aware of: Breakpoints, Debugger, and Variables:

The Breakpoints pane shows all the microflows that contain breakpoints, which makes it easier to find your breakpoints. The best practice is to remove any breakpoints after you are done troubleshooting your microflows. You can always delete them from the Breakpoints pane.

The Debugger pane is useful when you are debugging your microflow, as it will walk you through the microflow:

The Variables pane shows the variables, objects, and lists involved in your microflow and how they change as you step through the microflow via the Debugger pane:

The best practice is to have the Debugger and Variables panes in different docks. The Debugger pane should usually be at the bottom of your development dock, and the Variables pane can be either in the left dock or the side dock. You want to be aware of how the values are being changed in the microflow, and it is difficult to see those changes if both panes are tabs within the same dock.

Using Breakpoints

Breakpoints are points in a microflow where the application will halt execution. This is useful to analyze the application execution and data up to that point. You can add breakpoints at any point in your microflow by following these steps:

  1. Run your application locally.

  2. Open the microflow that needs debugging in Studio Pro.

  3. Right-click any of the activities or decisions in the microflow and select Add breakpoint. This sets a breakpoint on the selected step in the microflow, which is visually represented by a red dot:

    You can open an overview of all the breakpoints by going to View > Breakpoints:

    In the Breakpoints pane, you can enable, disable, and delete breakpoints. You can also configure a breakpoint condition and open the microflow that contains that breakpoint:

Debugging

  1. Run the application and open it in your browser.

  2. Do whatever is needed to trigger the microflow that you want to debug:

    • As an end-user of the application, you will see a progress bar on the application
    • As a developer of the application, you will see the Mendix icon flashing on the panes task bar

  3. Click the icon on the panes task bar to open Studio Pro. The element with the breakpoint that interrupts this microflow should be highlighted with a red border:

  4. Open the Debugger pane from the View menu:

    The debugger can be used to go through the microflow step by step:

  5. You have the following options on this pane:

    • Click Step into or Step over to move to the next step in the microflow (note that the difference between Step into and Step over is only noticeable if you run into a microflow call activity or a loop)
      • Step into means that the debugger steps into the sub microflow or loop
      • Step over moves the debugger to the next step in the same microflow
    • Click Step out to instruct the debugger to leave the sub microflow or loop (this is basically the opposite of Step Into)
    • Click Continue to instruct the debugger to continue until it reaches another breakpoint

For details on available shortcut keys, see the Debugger Shortcut Keys section of Studio Pro Overview.

Variables Viewer

As you are stepping through a microflow, the variables pane will start to change. This overview will show you all the variables, objects, and lists involved in the application, that is all the variables, entities, references, current-user information, and device-type information. It can be used as you are stepping through the microflow to review the values and see if they match your expectations.

You can open the Variables pane from the View menu:

The Variables viewer can be used to inspect values accessible to the microflow. The values are updated with every step you make in the Debugger:

Breakpoint Conditions

Sometimes it is necessary to configure a breakpoint so that the microflow only breaks on a certain condition. This is achieved with breakpoint conditions and is configured by use of microflow expressions. Setting a breakpoint condition can be very useful if you are debugging a batch process and you only want to break at a certain value. Using breakpoint conditions is strongly advised if you are debugging an application that is running in production, as this will prevent the application from stopping for users other than yourself.

To use breakpoint conditions, follow these steps:

  1. Right-click the activity or decision in the microflow with a breakpoint and select Edit breakpoint condition:

  2. Use the expression below to make sure this breakpoint only interrupts the microflow if you are executing it yourself (replace YourUserName with your own user name):

    $currentUser/name = 'YourUserName'

    The expression should look like this:

  3. Click OK to save the breakpoint condition.

Read More